MP- Lubricator, Air Line
Call Center

Coriolis Mass Flow Vortex Flow Meter
ROSS VALVES, Heavy Industrial Valve
Line Mounted Valve
Manual & Mechanical Valve
Air Preparation FRL
Safety Pneumatic Solution
Flow Control,Quick Exhaust, Shuttle&Check Valve
Base Mounted Valve
ROSS Type...
Dust Collector System
Diaphragm Valve
Explosion Proof Product
Remote Solenoid Enclosure and Remote Pilot
Electronic Control Systems
Immersion Header Tank
Bulkhead Connector
Sensor Transmitter and Controller
Flow sensor
Level Sensor
Analysis Sensor
Temperature sensor
Pressure Sensor
BURKERT Sensor Type
Chemical Chart
Pneumatic อุปกรณ์ในระบบลม
"PNEUMAX" Air Cylinder & Accessories
AIRTEC Solenoid Valve 32,52,53
MP Filter,Regulator,Lubricator.,Dryer,ServOil,Injection Lubricator
"BURKERT" Singular Valve
Fitting, Tube, Accessories
Solenoid Valve Process and Control Valve
Valve-water and other neutral media
Angle Seat Valve
Ball Valve
Valve-Neutral gas media
Globe valve
Pneumatic Quarterturn Actuator
Valve-Steam up to 180 C
Valve-High Pressure up to 250 bar
Control Head
Electric Quarterturn Actuator
Valve-High Pressure up to 250 bar
Positioner & Process Controller
Diaphragm valve
Valve-Aggressive media


MP- Lubricator, Air Line  
MP- Lubricators, Air LineMP- Lubricators, Air Line
MP- Lubricators, Air Line
รหัส : PR000L
ยี่ห้อ : MP U.S.A.
รุ่น : MP Lubricator, Air Line
รายละเอียดย่อ :
Master Pneumatic USA : Lubricators, Air Line size 1/4 to 11/2
Air line lubricators are designed to introduce atomized oil into the air line so that downstream mechanisms can be adequately lubricated. Lubricators should be adjusted so that the minimum amount of oil to lubricate the equipment is used. Excess oil will simply be blown into the atmosphere and pollute the environment.

There are two basic designs used in Master Pneumatic lubricators: sight-feed design and wick-feed design. Illustrations of these two types of assembly are shown on the facing page.
รายละเอียดทั้งหมด :

Master Pneumatic USA :  Lubricators, Air Line size 1/4 to 11/2

SIGHT-FEED LUBRICATORS  Air flows through a flexible-vane automatic flow sensor that creates a small pressure differential between the air passage and the oil reservoir. This differential causes oil to move up a riser tube, through an adjustable metering valve, and then to drip into a transparent dome and the air stream. This oil is “atomized” by the air stream, and carried down the air line to the points of lubrication. 
Sight-feed lubricators are easy to adjust, and an indicator on the sight dome measures the amount of oil dispensed.  The adjusting knob can be removed to make the lubricator “tamper-resistant.” 
All working parts are in an easily replaceable cartridge. Note: Not recommended for valve and cylinder circuits (see INJECTION LUBRICATORS section).

WICK-FEED LUBRICATORS  In a wick-feed lubricator one end of a porous bronze wick is saturated with oil in the reservoir. Capillary action causes the oil to travel up the wick. Oil is stripped off the upper portion of the wick by the air fl ow, and maintains a constant oil-to-air ratio. This ratio can be varied by manual adjustment. Units will not shut off, even with dirt and moisture in the reservoir. However, air must be shut off when filling the reservoirs of these models.

MODULAR or INLINE MOUNTING  SENTRY, GUARDSMAN, SERIES 380, and Full-Size VANGUARD lubricators are of modular design. They are connected to other units by special modular connectors which seal the faces between units. They may also be inline mounted with pipe nipples.  MINIATURE and High-Flow VANGUARD lubricators are inline mounted only.

MP Lubricator 1_4 to 1_12.pdf

MP Lubricators Printable.pdf

MP Intro Basic Lubrication.pdf

หากสนใจ กรุณากรอกรายละเอียดเพื่อติดต่อกลับ
บริษัท / Company :  *
ปรเภทกิจการ :
โทรศัพท์ / Tel. :  *
ชื่อของท่าน / Name :  *
นามสกุล / Surname :
ตำแหน่ง / Position :
มือถือ / Mobile :  *
อีเมล์ของท่าน / Email :  *
Line ID :
ติดต่อเกี่ยวกับ :
รายละเอียด :  *